Posted: Fri May 30th, 2014 02:57 pm |
|
1st Post |
zig Zeigler
Non AGG Member
Joined: | Fri May 30th, 2014 |
Location: | |
Posts: | 7 |
Status: |
Offline
|
back to top
|
Dalle de verre: I know that the recommendation is that no single panel be more than 12sf. But what is the maximum stacking height for 1" panels in a curtain-wall construction? 7 feet? 10 feet? 15 feet?
--zig
|
Posted: Sat May 31st, 2014 07:31 pm |
|
2nd Post |
Krueger
Senior Advisor
back to top
|
I would suggest you contact a structural engineer in your state, as specifications will vary from state to state....may need to assess general wind loads for the specific area of installation.
Barbara Krueger
Michigan Stained Glass Census
|
Posted: Mon Jun 2nd, 2014 03:37 pm |
|
3rd Post |
zig Zeigler
Non AGG Member
Joined: | Fri May 30th, 2014 |
Location: | |
Posts: | 7 |
Status: |
Offline
|
back to top
|
Thanks Barbara. I also have the query into Key Resin at Miamiville Distribution Center. I'll let you know what I hear from them. --zig
|
Posted: Wed Jun 4th, 2014 06:35 pm |
|
4th Post |
zig Zeigler
Non AGG Member
Joined: | Fri May 30th, 2014 |
Location: | |
Posts: | 7 |
Status: |
Offline
|
back to top
|
Talked with Bob Cain, the past president, CEO, and owner of Key Resin. He said they recommended 16sf as the maximum single panel size (though 12sf was better.) And he said panels should not be stacked more than 15' high. There would be special considerations, of course, if there was a lot of wind load--as there would be for any heavy plate glass installation.
|
Posted: Wed Jun 4th, 2014 08:41 pm |
|
5th Post |
Krueger
Senior Advisor
back to top
|
The local/state building code needs to be asked about their requirements, as some years ago this topic was discussed and in many hurricaine prone areas, exterior glazing was required on Dalle De Verre because it didn't pass their wind load tests.
Barbara Krueger, Michigan
|
Posted: Wed Jun 4th, 2014 09:14 pm |
|
6th Post |
zig Zeigler
Non AGG Member
Joined: | Fri May 30th, 2014 |
Location: | |
Posts: | 7 |
Status: |
Offline
|
back to top
|
Thanks. I will.
|
Posted: Fri Jun 6th, 2014 03:00 pm |
|
7th Post |
CZL
Senior Advisor
Joined: | Thu Oct 9th, 2008 |
Location: | |
Posts: | 144 |
Status: |
Offline
|
back to top
|
Nine squair feet. that is the max I ever did. I don't like to see the bottom one bend, and I have seen them do that. CZ
|
Posted: Fri Jun 6th, 2014 03:55 pm |
|
8th Post |
zig Zeigler
Non AGG Member
Joined: | Fri May 30th, 2014 |
Location: | |
Posts: | 7 |
Status: |
Offline
|
back to top
|
I had a panel bend as well at LESS than 9sf but that was because I didn't let it cure lying FLAT for one week. I stacked it on end leaning up against a wall. sigh.
|
Posted: Mon Jun 9th, 2014 11:06 pm |
|
9th Post |
CZL
Senior Advisor
Joined: | Thu Oct 9th, 2008 |
Location: | |
Posts: | 144 |
Status: |
Offline
|
back to top
|
Right It takes at least 14 days in a heated room to cure.
but that does not mean much in the WINTER. I watched them worp all over the place one winter back in the 70s.
Best to play it save. Don't stach um high and keep um warm and PRAY. CZ
|
|